A non-adhesive tag can solve an identification problem where sticking a label to the item is impractical. It also creates a different qualification task: the printed information must remain readable while the tag, its hole and the chosen fastening method keep the identifier with the correct item. A strong print on an unattached sample does not establish that complete result.
Specify the finished tag, not only the polymer
Record the material grade, printable side, finished dimensions, thickness, hole geometry and any perforation or registration feature. Include the intended attachment point and how the tag will be presented to the reader. A generic request for a polyethylene tag leaves both printing and mechanical details unresolved.
Brady's B-109 technical data sheet describes a matte, cross-laminated polyethylene tag printable by thermal transfer or dot matrix. It recommends Brady Series R4300 and R6200 thermal-transfer ribbons. These are references for the named material, not evidence that every polyethylene sheet or ribbon of a similar category is interchangeable. Brady B-109 technical data
Ask for a converted sample representing the proposed order. A plain sheet can help screen print compatibility, but it cannot show how the production hole, edge or perforation behaves. Keep the material identifier separate from the finished part number so a later change in converting geometry remains visible.
Reserve space for the hole and the actual print window
Do not assume that overall tag dimensions equal the usable image area. Brady's THT-33-109-0.5 product page lists a 6-inch by 3-inch tag but a printable area of 5.411 inches by 3 inches. Those dimensions belong to that finished format; they illustrate why the drawing and print window need separate fields. Brady finished-tag dimensions
Build the template from the approved drawing. Keep required text, barcode features and quiet zones clear of the hole, edge and separation area. Include the longest expected variable data when checking the layout. A short demonstration value can conceal a field that later extends into an unusable region.
Print a sequence at the production settings and check image placement through normal pauses and reloads. Confirm that the installed printer supports the stock thickness, width, feed arrangement and separation method. Use its documented sensing and calibration procedure; do not add an improvised mark or bypass a sensor to make an incompatible format feed.
Test the attachment separately from image durability
Agree the actual tie, loop or other approved fastener and the intended fixing point. Record how the tag is fitted, which way it hangs and whether it can turn, fold or rub against nearby parts during ordinary handling. A legible tag that detaches or migrates to another item has failed the identification task.
The B-109 sheet reports hole tear strength separately from tear propagation resistance and gives machine-direction and cross-direction results. These are laboratory material observations. They are not an allowable load for an assembled tag and fastener, and should not become a universal pull-test threshold. Brady mechanical test scope
Have the application owner define a safe, representative handling check. Examine the hole and surrounding material after the expected movements, not just the broad face. Record tearing, stretching, fastener damage and loss of the required reading position separately. Do not use an identification tag as a lifting or restraint component.
Match the exposure trial to the printed combination
Keep the ribbon reference, tag lot, printer model, resolution and effective settings with the samples. Check the smallest required text and the actual barcode before exposure, then repeat the agreed checks after the relevant handling or contact. The tag remaining intact is a different observation from the image remaining acceptable.
Brady's B-109 chemical testing identifies the two named ribbons and distinguishes observations before and after rubbing. A compatibility decision therefore needs the contact and handling conditions, not simply a broad description such as chemical-resistant. Brady printed-sample test method
For a replacement ribbon, retain an approved control and change one identified input at a time. Use the site's approved exposure method rather than inventing a more aggressive solvent test. Keep failed output alongside the final passing sample so the operating limits are not lost during purchasing review.
Approve the tag as it will actually be read
Assess the identifier in its fitted position. Check whether the fastener, a fold or the item itself obscures required information. Apply the specified barcode verification method and separately confirm that the operational reader captures the expected data. Record any limitations when the assembled geometry cannot be measured directly.
The release record should name the finished tag construction, ribbon, printer setup, artwork, fastening method and tests completed. State which item shapes and handling conditions were covered. A change to the hole, fastener or attachment point deserves review even if the printed face looks unchanged.
For controlled safety uses, retain the responsible site's approved tag and procedure requirements; a general printing trial does not establish that approval. For ordinary inventory or work-in-progress identification, the same purchasing discipline remains useful: order a reproducible printed-and-attached construction, rather than a material name plus an attractive loose sample.